0 item(s)
View cart
You have no items in your shopping cart.
Tie Rod End for Ford with 11/16"-18 RH Male Thread in Stainless Steel
Polished stainless steel
11/16”-18 right hand thread (male thread type)
Thread length: 2”
Includes castellated nut, split pin and grease nipple
Stud length: 3/4”
Stud diameter/thread: 1/2”-20
$70.60
Batwing Brackets Stainless Steel, Pair
Polished stainless steel
Suits 1928-48 Ford’s with i-beam axle
Suits axles with 2-1/4” boss
$210.05
Ford Cleveland 302 351 Performance Electric Water Pump 35GPM - Chrome
Suits Ford Cleveland 302 351 Not suitable for Windsor Chrome finish Aluminium construction 12 Volt 35 gallons per minute flow rating Eliminates parasitic horsepower loss due to impeller drag Inlet...
$380.90
Ford Cleveland 302 351 Performance Electric Water Pump 35GPM - Black
Suits Ford Cleveland 302 351 Not suitable for Windsor Black finish Aluminium construction 12 Volt 35 gallons per minute flow rating Eliminates parasitic horsepower loss due to impeller drag Inlet...
$350.90
Bumper Bar Plugs suit 1932 Ford Car & Truck, Polished Stainless Steel, Set of 4
Set of 4 bumper bar dress plugs to finish-off the open rolled ends of factory style 1932 Ford bumper bars Suitable for both 1932 Ford cars and trucks Overall diameter:...
$48.19
Daytona Cast Iron Pinion Support to suit Ford 9 Inch
Suits Ford 9 Inch Cast from 30,000psi gray iron Stronger than stock cast iron support Improved oil flow compared to stock cast iron support Utilises standard Ford 9" front pinion...
$149.55
Daytona Billet Aluminium Pinion Support to suit Ford 9 Inch
Suits Ford 9 Inch Black anodised billet aluminium Stronger than stock cast iron support Utilises standard Ford 9" front pinion bearing and the Daytona style pinion bearing on the rear...
$137.55
Differential Housing Gasket to suit Ford 9 Inch
Suits Ford 9 Inch
Paper fibre style
Precision die cut
$24.65
Pinion Crush Sleeve to suit Ford 9 Inch
Suits Ford 9 Inch Replacement for stock style crush sleeve/collar Collapsible spacer installs on the pinion and preloads the pinion bearings Note: crush sleeves are not reusable and must be...
$21.49
Pinion Shim Master Kit to suit Ford 9 Inch
Suits Ford 9 Inch
Includes:
Pinion bearing housing shims
Pinion bearing shims
Pinion crush sleeve
Pinion nut
Note: this is a shim kit only. There are no bearings or gaskets.
$52.00
Pinion Support Bolts to suit Ford 9 Inch Daytona Support to Iron Housing
Suits Ford 9 Inch
Designed to suit the Daytona style pinion support, being attached to an iron housing
$45.65
Third Member Axle Housing Carrier Studs to suit Ford 9 Inch
Suits Ford 9 Inch 3/8"-24 thread size Ideal for your new rear end or for replacing old/damaged studs The non-threaded ends aid in aligning the third member housing without damaging...
$49.38
1310 Series Pinion Yoke, Short Style, to suit Ford 9 Inch
Suits Ford 9 Inch Fits 28 spline 1.218" pinion gear Reproduction of the original For "short" pinion yoke Integrated dust cover Forged steel Suits 1310 series u-joints Measurements: Overall length:...
$126.25
Pinion Nut to suit Ford 9 Inch
Suits Ford 9 Inch
Steel pinion nut
3/4"-16 thread
Red thread locking compound pre-applied
$17.65
Viton Pinion Seal to suit Ford 9 Inch
Suits Ford 9 Inch
Viton construction provides better heat tolerance when compared to stock rubber seal
Rated to approx 400°F. Stock seal starts to break down at 250°F
$24.65
Water Pump suits 1938-53 Ford Flathead V8 Engines R/H Side, Cast Iron
To suit Ford Flathead V8 (1938-1953) Direct replacement for OEM pump Cast iron This is the right hand side mounting pump Refer to USM-US20 for the left hand side pump...
$180.03
Water Pump suits 1938-53 Ford Flathead V8 Engines L/H Side, Cast Iron
To suit Ford Flathead V8 (1938-1953) Direct replacement for OEM pump Cast iron This is the left hand side mounting pump Refer to USM-US19 for the right hand side pump...
$180.00
Water Pump suits Ford Windsor 289 302 351W Engines, Left Hand Inlet, Cast Iron
To suit Ford Windsor 289 302 351W with a left hand inlet pump Direct replacement for OEM pump Cast iron Includes gasket All US Motor Works mechanical water pumps are...
$145.95
Water Pump suits 1965-76 Ford FE 390 428 Engines, Cast Iron
To suit Ford FE 390 428 engines (1965-1976) Direct replacement for OEM pump Cast iron Includes gaskets All US Motor Works mechanical water pumps are designed and tested to meet...
$215.95
Water Pump suits Ford Big Block 429 460 Engines, Cast Iron
To suit Ford Big Block 429 460 engines Direct replacement for OEM pump Cast iron Includes gaskets All US Motor Works mechanical water pumps are designed and tested to meet...
$151.50
